Linked e-resources
Details
Table of Contents
Intro
Preface
Contents
About the Editors
Electro-Physical and Chemical Machining
A Sustainable Die-Sinking Electrical Discharge Machining of Ti6Al4V Using Jatropha Bio-Dielectric
1 Introduction
2 Materials and Methods
3 Results and Discussion
4 Conclusion
References
Comparative Evaluation of Machining Performance of Nimonic 263 in Powder Mixed EDM
1 Introduction
2 Materials and Methods
2.1 Materials
2.2 Methodology
3 Results and Discussion
3.1 Effect of Process Parameters on MRR
3.2 Effect of Process Parameters on TWR
3.3 Effect of Process Parameters on Ra
3.4 Optimum Condition
3.5 Residual stress
4 Conclusion
References
Effect of Peak Current and Pulse-On Time on MRR and TWR in EDM of Ti-6Al-4 V
1 Introduction
2 Materials and Methods
3 Results and Discussions
3.1 Material Removal Rate (MRR)
3.2 Tool Wear Rate (TWR)
4 Conclusions
References
Electro Discharge Machining of Advanced Engineering Ceramics
1 Introduction
2 Materials and Method
3 Results and Discussions
3.1 Effect of Peak Amount of Current (Ip) on MRR
3.2 Influence of Time Period of Keeping on (Ton) Over MRR
3.3 Impact of Flushing Pressure on MRR
3.4 Effect of Tool Shape
3.5 Effect of Workpiece Thickness
4 Conclusions
References
Enhancement of MRR of Inconel 718 During EDM by Numerical and Experimental Approaches
1 Introduction
2 Materials and Process Parameters
3 Thermal Modeling of EDM Process
4 Simulation Step
5 Experimental Setup
6 Results and Discussions
6.1 Model Validation
6.2 Regression Model Analysis of MRR
6.3 Variation of Crater Radius and Depth with Temperature
6.4 Effect of Machining Parameters on MRR
7 Conclusions
References
Experimental Investigation into Electrochemical Discharge Milling of Glass by Bottom Feeding the Tool Electrode
1 Introduction
2 Experimentation
2.1 Experimental Setup
2.2 Experiment Planning
3 Results and Discussion
3.1 Gas Film Generation Mechanism
3.2 Effect of Voltage and Electrolyte on the Generation of Electrochemical Discharge
3.3 Effects of Voltage and Electrolyte on the Machining Quality
3.4 Effect of Dwell Time on the Machining Quality
4 Conclusions
References
Experimental Investigations into Erosion of Zinc-Coated Brass Wire Electrode During WEDM of Ti-6Al-4 V Alloy
1 Introduction
2 Materials and Methods
3 Results and Discussion
3.1 Effects of Process Conditions on Wire Erosion
4 Conclusions
References
Improving Material Removal Rate in Machining of Micro-holes Using Hybrid EDM Process
1 Introduction
2 Materials and Methods
2.1 Method of Measurements
3 Experimental Setup
3.1 Non-hybrid Experimental Setup
3.2 Hybrid Experimental Setup
4 Experimental Design
5 Experimentation
6 Results and Discussion
Preface
Contents
About the Editors
Electro-Physical and Chemical Machining
A Sustainable Die-Sinking Electrical Discharge Machining of Ti6Al4V Using Jatropha Bio-Dielectric
1 Introduction
2 Materials and Methods
3 Results and Discussion
4 Conclusion
References
Comparative Evaluation of Machining Performance of Nimonic 263 in Powder Mixed EDM
1 Introduction
2 Materials and Methods
2.1 Materials
2.2 Methodology
3 Results and Discussion
3.1 Effect of Process Parameters on MRR
3.2 Effect of Process Parameters on TWR
3.3 Effect of Process Parameters on Ra
3.4 Optimum Condition
3.5 Residual stress
4 Conclusion
References
Effect of Peak Current and Pulse-On Time on MRR and TWR in EDM of Ti-6Al-4 V
1 Introduction
2 Materials and Methods
3 Results and Discussions
3.1 Material Removal Rate (MRR)
3.2 Tool Wear Rate (TWR)
4 Conclusions
References
Electro Discharge Machining of Advanced Engineering Ceramics
1 Introduction
2 Materials and Method
3 Results and Discussions
3.1 Effect of Peak Amount of Current (Ip) on MRR
3.2 Influence of Time Period of Keeping on (Ton) Over MRR
3.3 Impact of Flushing Pressure on MRR
3.4 Effect of Tool Shape
3.5 Effect of Workpiece Thickness
4 Conclusions
References
Enhancement of MRR of Inconel 718 During EDM by Numerical and Experimental Approaches
1 Introduction
2 Materials and Process Parameters
3 Thermal Modeling of EDM Process
4 Simulation Step
5 Experimental Setup
6 Results and Discussions
6.1 Model Validation
6.2 Regression Model Analysis of MRR
6.3 Variation of Crater Radius and Depth with Temperature
6.4 Effect of Machining Parameters on MRR
7 Conclusions
References
Experimental Investigation into Electrochemical Discharge Milling of Glass by Bottom Feeding the Tool Electrode
1 Introduction
2 Experimentation
2.1 Experimental Setup
2.2 Experiment Planning
3 Results and Discussion
3.1 Gas Film Generation Mechanism
3.2 Effect of Voltage and Electrolyte on the Generation of Electrochemical Discharge
3.3 Effects of Voltage and Electrolyte on the Machining Quality
3.4 Effect of Dwell Time on the Machining Quality
4 Conclusions
References
Experimental Investigations into Erosion of Zinc-Coated Brass Wire Electrode During WEDM of Ti-6Al-4 V Alloy
1 Introduction
2 Materials and Methods
3 Results and Discussion
3.1 Effects of Process Conditions on Wire Erosion
4 Conclusions
References
Improving Material Removal Rate in Machining of Micro-holes Using Hybrid EDM Process
1 Introduction
2 Materials and Methods
2.1 Method of Measurements
3 Experimental Setup
3.1 Non-hybrid Experimental Setup
3.2 Hybrid Experimental Setup
4 Experimental Design
5 Experimentation
6 Results and Discussion